You can change the passwords:
• in the General > Device info setting view in Easergy Pro
connected to the USB port in the relay's front panel
• via Ethernet using Easergy Pro or the web server
NOTE: The password can contain 1-16 digits (no alphabets).
It is possible to restore a password if the password is lost or forgotten.
To restore a password, a relay program is needed. The virtual serial
port settings are 38400 bps, 8 data bits, no parity and 1 stop bit. The
bit rate is configurable via the front panel.
using the following commands
get pwd_break ---------------Get the break code (Example: 6569403)
get serno -------------------Get the serial number of the relay (Example: 12345)
Send both numbers to your nearest Schneider Electric Customer
Care Centre and ask for a password break. A relay-specific break
code is sent back to you. That code is valid for the next two weeks.
using the following commands
set pwd_break=4435876 ----------Restore the factory default passwords (“4435876” is just an example.
The actual code should be asked from your nearest Schneider Electric
Customer Care Centre.)
Now the passwords are restored to the default values.
• in the General > Device info setting view in Easergy Pro
connected to the USB port in the relay's front panel
• via Ethernet using Easergy Pro or the web server
NOTE: The password can contain 1-16 digits (no alphabets).
It is possible to restore a password if the password is lost or forgotten.
To restore a password, a relay program is needed. The virtual serial
port settings are 38400 bps, 8 data bits, no parity and 1 stop bit. The
bit rate is configurable via the front panel.
using the following commands
get pwd_break ---------------Get the break code (Example: 6569403)
get serno -------------------Get the serial number of the relay (Example: 12345)
Send both numbers to your nearest Schneider Electric Customer
Care Centre and ask for a password break. A relay-specific break
code is sent back to you. That code is valid for the next two weeks.
using the following commands
set pwd_break=4435876 ----------Restore the factory default passwords (“4435876” is just an example.
The actual code should be asked from your nearest Schneider Electric
Customer Care Centre.)
Now the passwords are restored to the default values.
Released for:Schneider Electric India
You can change the passwords:
• in the General > Device info setting view in Easergy Pro
connected to the USB port in the relay's front panel
• via Ethernet using Easergy Pro or the web server
NOTE: The password can contain 1-16 digits (no alphabets).
It is possible to restore a password if the password is lost or forgotten.
To restore a password, a relay program is needed. The virtual serial
port settings are 38400 bps, 8 data bits, no parity and 1 stop bit. The
bit rate is configurable via the front panel.
using the following commands
get pwd_break ---------------Get the break code (Example: 6569403)
get serno -------------------Get the serial number of the relay (Example: 12345)
Send both numbers to your nearest Schneider Electric Customer
Care Centre and ask for a password break. A relay-specific break
code is sent back to you. That code is valid for the next two weeks.
using the following commands
set pwd_break=4435876 ----------Restore the factory default passwords (“4435876” is just an example.
The actual code should be asked from your nearest Schneider Electric
Customer Care Centre.)
Now the passwords are restored to the default values.
• in the General > Device info setting view in Easergy Pro
connected to the USB port in the relay's front panel
• via Ethernet using Easergy Pro or the web server
NOTE: The password can contain 1-16 digits (no alphabets).
It is possible to restore a password if the password is lost or forgotten.
To restore a password, a relay program is needed. The virtual serial
port settings are 38400 bps, 8 data bits, no parity and 1 stop bit. The
bit rate is configurable via the front panel.
using the following commands
get pwd_break ---------------Get the break code (Example: 6569403)
get serno -------------------Get the serial number of the relay (Example: 12345)
Send both numbers to your nearest Schneider Electric Customer
Care Centre and ask for a password break. A relay-specific break
code is sent back to you. That code is valid for the next two weeks.
using the following commands
set pwd_break=4435876 ----------Restore the factory default passwords (“4435876” is just an example.
The actual code should be asked from your nearest Schneider Electric
Customer Care Centre.)
Now the passwords are restored to the default values.
Released for:Schneider Electric India
